• Available volume : 160 & 200 litres
  
• Direct Heat or Water Jacket Models
• Infra Red CO2 Sensor
  
• Chamber in positive pressure
• Hepa Filtration to achieve ISO Class 5 Clean Room’s environment.
• Hepa filters are fitted outside the culture chamber, in a easy to reach front panel compartment.
  
• Nu-Touch Control Center : Easy to use – intuitive icons – touch panel system
  
• Dual Sterilization cycle (dry & wet)  (option)
  
• Active control of the Humidity level (option)
  
• Oxygen level control (option)
  
• Copper “Cu Verro” chamber (option)
  
• Sectionned glass window (option)
• Check the video here below to learn more & download the complete brochure at the end of this webpage
  

Nuaire Infra Red CO2 Incubator

Dual Wave Infra Red CO2 Sensor

A microprocessor-based, non-dispersive, single source dual wave infrared (IR) sensor monitors and controls CO₂ levels inside the growth chamber. Wavelengths are only absorbed by CO₂ making measurement insensitive to other components, such as water vapor. The stable IR sensor has a controlled range of 0.1 to 20% accurate within 0.1%.

Constant Contamination Control (C³) :

I. Closed Loop HEPA Filtration :

A maintenance free air pump continuously draws environmental samples from two locations inside the chamber and passes the sample through a 99.99% HEPA filter before entering the sensor bay to measure gas. The IR sensor measures CO2 gas levels from the sample to monitor before entering the sensor bay to measure gas. The IR sensor measures CO2 gas levels from the sample to monitor before injecting back into the growth chamber. The NuTouch Electronic Control system will then determine the appropriate course of action to maintain chamber set-point conditions by placing the system on standby or injecting 99.99% HEPA filtered CO2 gas or air into the growth environment.

II. ISO Class 5 Cleanroom Conditions :

Based on clean room technology, In-VitroCell maintains the growth chamber at positive pressure similar to an ISO Class 5 Clean room to slow airflow to minimize desiccation. Anytime the chamber door is open to the laboratory environment, clean HEPA filtered will be forced out instead of contaminated lab air being drawn in.

III. Temperature Uniformity :

The chamber walls are surrounded by five (5) heating elements to control temperature. A door heater is separately controlled to minimize condensation on the inner chamber door. The heating elements are wrapped in a high density R5 insulation to maintain temperature integrity. Dual temperature sensor probes monitor and control temperature set points to ensure consistency and uniformity throughout the chamber.

Advanced Construction :

Attention to Proper Materials and Construction Methods :

The inner chamber is constructed of high grade 16 gauge, type 304L polished stainless steel using crevice-free construction that provides an easily cleanable inert surface that does NOT promote biological growth. Seamless coved interior corners are easily cleaned promoting a healthy growth chamber. A single piece gasket creates a liquid tight seal from incubator chamber to inner door to eliminate condensation build up and potential contamination. Inner chamber shelving and gasket may be removed and routinely autoclaved if desired.

Small Footprint, Incredibility Large Useable Space :

A large 200 litres growth chamber comes standard with four incubator shelves with a maximum capacity of 23 shelves. By attaching heating elements directly to the chamber and insulating with High Density R5 insulation In-VitroCell was engineered as a compact design while maximizing chamber capacity.

Upgrade Your System :

CuVerro® Antimicrobial Copper Surfaces (Optional Feature) :

Add CuVerro® Antimicrobial Copper Surfaces to the incubator growth chamber and/or shelving to kill bacteria* to minimize potential incubator contamination. CuVerro® is laboratory tested and EPA registered. CuVerro® Antimicrobial Copper Surfaces kill more than 99.9% of bacteria* within 2 hours, and continues to kill 99% of bacteria* even after repeated contamination, when cleaned regularly.

EPA Reg No 85353-5

EPA Est No 088257-MN-001

*Laboratory testing shows that, when cleaned regularly, CuVerro® antimicrobial copper surfaces kill greater than 99.9% of the following bacteria within 2 hours of exposure: MRSA, Staphylococcus aureus, Enterobacter aerogenes, Pseudomonas aeruginosa, and E. coli O157:H7. CuVerro® antimicrobial copper surfaces are a supplement to and not a substitute for standard infection control practices and have been shown to reduce microbial contamination, but do not necessarily prevent cross contamination; users must continue to follow all current infection control practices, including those practices related to cleaning and disinfection of environmental surfaces.

Standard Features :

4 x  Stainless Steel Shelves / Right Hinge Door Swing / Remote Alarm Output Contacts / 4 to 20 mA Analog Output / RS-485 Communication / USB Port / CO2 Sample Port / Adjustable Leg Levelers

Access Port and plug with breather holes

1 x  Water Pan

1 x  2 m Electrical Cord

Contact us for more information.